Entry
Element Collection
-
-
-
-
-
Edge Collection
-
-
-
-
Patio
Passage
Privacy
Bluetooth
Strikes
Misc.
VIEW installation videos
Grip to Lever Mortise Lock
- Step 1. Mark the Door
- Step 2. Compare Lock, Hardware Trim and Door Conditions
- Step 3. Mortise Lock Cavity
- Step 4. Mortising Lock Front
- Step 5. Cut Relief Pockets
- Step 6. Mark Face of Door Lever to Lever
- Step 7. Drill Holes
- Step 8. Adjust Bevel and Install Lock
- Step 9. Grip to Lever Preparation
- Step 10. Install the Cylinder
- Step 11. Attach Exterior Lock Trim
- Step 12. Attach Interior Lock Trim
- Step 13. Install Scalp
Lever to Lever or Knob to Knob Mortise Lock
- Step 1. Mark the Door
- Step 2. Compare Lock, Hardware Trim and Door Conditions
- Step 3. Mortise Lock Cavity
- Step 4. Mortising Lock Front
- Step 5. Cut Relief Pockets
- Step 6. Mark Face of Door Lever to Lever
- Step 7. Drill Holes
- Step 8. Adjust Bevel and Install Lock
- Step 9. Lever to Lever Preparation
- Step 10. Install the Cylinder
- Step 11. Attach Exterior Lock Trim
- Step 12. Attach Interior Lock Trim
- Step 13. Install Scalp
Grip to Grip Mortise Lock
- Step 1. Mark the Door
- Step 2. Compare Lock, Hardware Trim and Door Conditions
- Step 3. Mortise Lock Cavity
- Step 4. Mortising Lock Front
- Step 5. Cut Relief Pockets
- Step 6. Mark Face of Door
- Step 7. Grip by Grip Preparation
- Step 8. Install the Cylinder
- Step 9. Attach Exterior and Interior Lock Trim
- Step 10. Install Scalp
- Step 11. Lock Operation
Spring Latch Dead Bolt
- Step 1: Door Preparation
- Step 2: Drill the Edge Bores
- Step 2A: Drill the Edge Bores Freehand
- Step 2B: Drill the Edge Bores with a Boring Jig
- Step 3A: Drill all Facebores
- Step 3B: Drill all Facebores
- Step 3C: Drill the Face Bores with a Boring Jig
- Step 4: Trace the Faceplates
- Step 5: Mortise Faceplates
- Step 5A: Mortise Faceplates With a Router
- Step 6: Install Spring Latch and Dead Bolt
- Step 7: Drill Pilot Holes
- Part 2 - Step 1: Trim Installation
- Part 2 - Step 2: Install Exterior and Interior Trim
- Part 2 - Step 3: Cylinder Installation
- Part 2 - Step 4: Mounting Plate Installation
- Part 2 - Step 5: Install Interior Trim
- Part 2 - Step 6: Drill Pilot Holes
- Part 2 - Step 7: Check Operation
Dead Bolt
- Part 1 - Step 1. Mark the Door
- Part 1 - Step 2. Drill the Edge Bore
- Part 1 - Step 2A. Drill the Edge Bore using a Boring Jig
- Part 1 - Step 3. Mark the Faceplate
- Part 1 - Step 4. Chisel Plate Mortise
- Part 1 - Step 4A. Mortise Faceplate with Router
- Part 1 - Step 4B. Chisel Corners
- Part 1 - Step 5. Bore the Face
- Part 1 - Step 5A. Bore the Face with a Boring Jig
- Part 1 - Step 6. Install Dead Bolt
- Part 2 - Step 1. Cylinder Installation
- Part 2 - Step 2. Mounting Plate Installation
- Part 2 - Step 3. Turn Piece Escutcheon Installation
Privacy or Passage Spring Latch Set
- Part 1 - Privacy Passage Installation
- Part 1 - Step 1. Mark the Door
- Part 1 - Step 2. Drill the Edge Bore
- Part 1 - Step 3. Drill the Face Bore
- Part 1 - Step 4. Trace the Faceplate
- Part 1 - Step 5. Mortise Faceplate with a Chisel
- Part 1 - Step 5A. Mortise Faceplate with a Router
- Part 1 - Step 6. Chisel Corner
- Part 1 - Step 7. Drill Pilot Holes for Faceplate
- Part 1 - Step 8. Adjust Bevel for Privacy
- Part 1 - Step 9. Adjust Latch for Passage
- Part 1 - Step 10. Fasten Latch
- Part 2 - Trim Installation
- Part 2 - Step 1. Spindle Installation
- Part 2 - Step 2. Install Exterior and Interior Trim
- Part 2 - Step 3. Check Operation